BOC4x4 Poisoning (new page 53) 美式放毒區 (第53页新)

目的地西藏

原帖由 抄收了 于 2009-12-6 18:27 发表
大概样子做好了,,灯支架还没有做上去.今天试装了一下新款帕拉丁尺寸有点不一样,问一下,新老款帕拉丁行里架是不是一样的

要是我就把Paladin的字样直接改成Xterra...
期待成品...

洋海盗

强车，牛人，顶了！

BOC

Today I received my set of 4 Staun Internal Beadlocks.  This device is fitted to the wheel, inside the tire.  When inflated, it 100% locks the tire bead to the rim so that you can run your tires at very low pressure to improve driving performance on beach sand, desert sand, mud and rocks.

I will post the install pictures next week after my Christmas holiday

[ 本帖最后由 BOC 于 2009-12-22 22:38 编辑 ]

城市农民3721

在低胎压下，防止撮胎的东东。

BOC

You can read more about them here http://www.staunproducts.com/beadlock.php

Below is the copy from the Staun site of the racing teams that use this product

Staun Racings Internal Beadlocks perform in the Dresden Breslau Rally

Mud Sand or Dirt, It doesn't matter! Staun Internal Beadlocks prove themselves again. Last Month in the Dresden-Breslau Rally held in Dresden Germany and Breslau Poland, Staun Racing and its Polish distributor of Staun Racing products took out the biggest Off Road Rally in Europe with a win and third place in the 4wd section of this extremely tough event.  The event is held over 6 days and with a mix of Sand, lots of Mud and dirt roads. The beadlocks and competitors were put through the toughest of terrain and conditions.

Congratulations to Driver Pawel Oleszczak and co driver and StaunRacing Distributor Maciej Chelmicki for preparing their Nissan GUPatrol to give a faultless run in this amazing event. No tyre problemsand No rim problems. A testament to Staun Racings Internal Beadlocks.

Congratulations also to the 20 teams that ran the beadlocks in their Cars for this event with great success for the product.                                                                                                                                                                                                                                    


[ 本帖最后由 BOC 于 2009-12-22 19:46 编辑 ]

lieren

原帖由 BOC 于 2009-11-3 19:26 发表
Today, I finally installed the Warn Premium Manual Locking Hubs （Warn手动前桥轮毂锁止器).  The installation was extremely quick and not very difficult.  You have to make sure that you remove all of t ...

这个东西不错，有没有具体的型号？我的自动轴头离合器也坏了，目前还处于半正常状态，琢磨着换个手动的还牢靠点。

城市农民3721

原帖由 lieren 于 2009-12-22 19:45 发表

这个东西不错，有没有具体的型号？我的自动轴头离合器也坏了，目前还处于半正常状态，琢磨着换个手动的还牢靠点。

他是从4X4parts.com上买的，那上面也没讲具体型号，只讲了是给哪年的Xterra配的。

https://www.4x4parts.com/catalog ... amp;products_id=720

[ 本帖最后由 城市农民3721 于 2009-12-22 19:49 编辑 ]

BOC

原帖由 lieren 于 2009-12-22 19:45 发表

这个东西不错，有没有具体的型号？我的自动轴头离合器也坏了，目前还处于半正常状态，琢磨着换个手动的还牢靠点。

I would recommend changing to manual hubs.  But if you don't want to do that, you can have the original hubs that were on my Paladin.  Of course the automatic hubs are not new, but they were working fine when I made the change.  If they work on the XE model, I would be more than happy to send them to you.

城市农民3721

Cool!

猎版你把地址给BOC吧。

BOC

So I get this package today ....

.... and I had the pleasure of meeting the famous "little cat"!

It was really fun meeting him at the garage and I hope that we can meet again in Shanghai!

[ 本帖最后由 BOC 于 2010-1-4 21:32 编辑 ]

BOC

I finally received my rear bumper today from SkoPri.  I have to say that while the bar is OK, there are some things about it that I think could have been done better.  The first thing I noticed was that the method of attaching the bumper to the frame is not as strong or secure as it should be.  There are two small pieces that bolt to the outside of the frame.  I don't think that this is going to support the weight of the tire while going off-road.  Nor do I feel that I can pull another truck without the risk of losing my bumper in the process.

The second thing that was not so good was the powder-coating.  It was already flaking off in several places and we had not even installed it yet.

The bumper was not a good fit and there was a certain amount of cutting and grinding involved to get it installed.  It may have been better for me to go to their workshop to have it fitted to the Paladin instead of doing it from Shanghai.

Overall it is not a bad piece, just a few things that I hope will not cause problems for me later.

冉昊

哈。。。。BOC的改装之路还在继续。。。

笑看风云淡

哈哈,这个杠是哪家的掉漆了哦

吉没泥

I am also interested in the SKOpri front and rear bumper, but seems that there are still some things need to be done as you just mentioned.

BOC

原帖由 吉没泥 于 2010-1-5 09:03 发表
I am also interested in the SKOpri front and rear bumper, but seems that there are still some things need to be done as you just mentioned.

I have been thinking all night of how to reinforce the rear bar so that it is more functional for off-road.  I have some modifications that I will make to it this week and post them for you to see.  If you like the ideas, maybe Skopri can do it for you straight from the factory.

My main concern is how the bar attaches to the frame.  It seems that the bar was made more for style than function.

offroad_city

BOC 是实实在在的自力更生

让心放飞

BOC改车很有心得

让心放飞

BOC改车很专业,前扛怎么不一起换了

nighttime

   备胎架 好家伙！

lieren

和BOC很像的改装风格